Posts Tagged ‘Panel’

Thermo Siphon Air Panel from CoroPlast Solar Heat Feasibility

GreenPowerScience showed us how to make a Thermo Siphon Air Panel using a sheet of cardboard. Basically it’s a solar heater made out of cheap materials, which will create a natural air draft as it is heated by the sun; sucking cold air in the bottom, and exhausting warm air out the top. As per GPS’s suggestion at the end of his video, I took the concept a step further with a 4×8 sheet of 1/4″ coroplast which I spray painted black. The sheet had a tendency to warp as it warmed up and the lack of insulation on the bottom side allowed it to be cooled simultaneously. This was done on a day in December when we had an ambient air temperature of 60 degrees F. The panel warmed the air to 82 or 83 degrees F. The panel never got too hot to touch. In Pennsylvania, the sun is pretty low in the winter time. I worried about GPS’s shop vac motor added any heat gain to his experiment, but once you read the comments, you’ll find that while it did initially, after 2 minutes of running, the vaccume output was only 5 degrees higher than the ambient in the 89 degree range… so he was getting +40 degrees with the cardboard lying on the ground, on what I would guess was a warmer summer day with the sun high overhead. My next steps are to build a frame with multiple input and output ports, insulate the back of the panel with 2″ foam, and cover it with of sheet of lexan or plexiglass. I would love to heat my basement with one or two of these panels. Check out my channel for an upcoming video on …

Build Solar Panel For Your Home

Build Solar Panel For Your Home

You want to build solar panels for your home to save money on your electric bill, produce eco friendly energy, or maybe both. Whatever the case, building your own solar panel is not hard.

Get Best Make Solar Panel and Make Wind Turbine Guide

Many people are building there own panels, because they found out that it is easier to do then they thought. They also like the benefits they get from having there own panels.

There are two ways that you can build your own solar panels for your homes.

Build From Scratch

What you need:

wood blocks insulation copper coil aluminum foil aluminum black sheet plexiglass caulk cordless drill and screws Get Best Make Solar Panel and Make Wind Turbine Guide

Make a square box using the wood blocks and install insulation on the bottom. Use your cordless drill and screws to assemble the wooden box.

Next you should insert the copper coil on top of the insulation; this will absorb heat. Now you should use aluminum foil to keep the absorbed heat and seal it with caulk.

The last step is to put the aluminum black sheet on top, then mount your plexiglass over the sheet. That’s all there is to building it from scratch.

Use A Solar Kit

If the first option might seem to technical, you can use solar kits instead to build solar panels.

The kit comes with all the necessary components, such as solar cells, solder, etc. You have to follow the instructions that come with the kit. These instructions are not hard to follow, but pay attention to the details.

Once you are done, it will be clear sailing for you. So take the step and spoil your family and yourself with free eco-friendly electricity. Once you start using solar, you will ask yourself why you did not start sooner.

Get Best Make Solar Panel and Make Wind Turbine Guide

How to Make a Solar Panel from Scratch

How to Make a Solar Panel from Scratch

Learning how to make a solar panel from scratch is a fun and you even don’t need to have any extra skills for that. This article will give you a very brief yet clear DIY guide on building a solar panel from scratch, i.e. things that are of no use to you rather than throwing it to the dust bin or those things that are valuable yet find no use right now.  So get ready to learn something new today by spending a few minutes in reading this article.

Learn to Make a Solar Panel at Home in Less than 0

Required Items:

Well, the required items are only things that are in and around your household and you need not take pains to buy something new for making a solar panel here.  The necessary items required are listed below;

Screwdriver A wood saw.  (An electronic wood saw shall be preferred rather than a hand saw) Soldering gun Drilling machine Copper wires Cutter for cutting wires. Paint brush. Electrical Solder Sheet of plexiglass. Silicon caulk. Rosin flux pen.

These were some of the items you need necessarily to make full use of the scratch items which are to be used to build a solar panel.  The scratch items that are going to be used are listed below;

Plywood of considerable length and width Tin wires

However there are certain items that have to be bought from a hardware shop.  They are solar cells and UV protective varnish.  But even this can be avoided if you had used a solar panel already.

Procedure:

Cut the plywood in dimensions that could accommodate all the solar cells and paint the cut plywood with UV protective varnish. Connect each cell to each other using wires and soldering them.  But before that make sure to apply flux to all the connector strips in cells using the Rosin flux pen. Attach these cells to the plywood using silicon caulk dabs. Make sure to accommodate holes for the two wires that have to be pulled from the last solar cell. Once the wires have been fed through these holes it is of utmost importance that you seal it using silicon beads. The next step is to drill holes in the plexiglass to accommodate screws through them. Build a frame to support the plexiglass. With the help of silicon and screws attach the plexiglass frame to the plywood containing the solar cells. Thus your solar panel is ready.  Make sure that you have assembled all parts carefully.

Diy Solar Panel Kits ? Top 3 Mistakes That A Beginner Must Avoid When Building A Solar Panel!

Alright fellow beginners, if you’re planning to put together your very own DIY solar panel kits, then please take note of the mistakes outlined below.

I made these mistakes when I first started out and needless to say…

They caused me a lot of grief!

Okay so here are the top 3 mistakes that you must avoid when making your first solar panel kits…

Mistake No.1 – Spending more than what is needed.

You know, my first project I spent more than what was necessary…

I bought an expensive plywood panel along with a fairly pricey glass sheet to cover the solar cells.

Quite a fair amount of cash wasted there!

Truth of the matter is you can make your own solar panel setup using inexpensive plywood panel. As long as it’s durable enough to hold the solar cells together, then you’re good to go!

Same goes for the glass sheet. Inexpensive Plexiglass sheet should suffice for your DIY solar panel kits!

My first attempt was a failure…

Anyway I had to purchase a new plywood panel and glass sheet.

Okay what about my second attempt?

It was a success and best of all…

The total cost only amounted to $206!

Mistake No.2 – Incorrect Wiring.

This mistake is quite common amongst beginners.

When doing the wiring configuration, ensure that the positive and the negative ending of the wires do not come into contact with one another.

To get a better understanding of this, we need to learn from…

Mistake No.3 – Beginners are Too Reliant on Printed Manuals.

It’s not a good idea for beginners to depend solely on printed manuals.

For me, the wiring process is the trickiest aspect of building a solar panel so it’s highly beneficial that we beginners refer to video instructions to get the entire process right.

Before I downloaded the instructional videos, I referred to printed manuals exclusively and it proved to be difficult!

Too many confusing jargons and diagrams killed my enthusiasm. I just couldn’t get the assembling process right!

If you watch instructional videos that are beginner-friendly, I‘m very sure that you’ll be able to assemble those DIY solar panel kits without much hiccups!

The 6 Step Basic Blueprint For Novices To Make Homemade Solar Panel!

Are you ready to make homemade solar panel?

One thing you need to remember is that building homemade solar panel is quite simple and doesn’t require extensive technical know-how.

Okay, here’s a basic 6 step blueprint to make homemade solar panel which I learned from viewing step-by-step video tutorials downloaded to my computer hard drive.

Head over to your nearest hardware store and acquire the following items:

1)    Blocking diodes
2)    Copper wires
3)    One sheet of Plexiglass
4)    Plywood Panel
5)    Silicone Sealant
6)    Solar cells
7)    Solder and soldering pen
8)    Stainless steel screws
9)    UV coating paint
10)     Wood to form panel border

My total cost: $206

1) Cut up the plywood according to the amount of solar cells you have in possession. To generate say 100 watts of power, you’ll need about 80 solar cells. Build and combine multiple panels if you require more power.

2) Paint the plywood panel with UV coating paint. Once done, you can start joining the solar cells together. Place all the cells on the ground and using the soldering pen, drop very little amount of solder onto the small tabs found at the back of each solar cell.

3) The solder applied on the tabs allows you to link all the cells together with the copper wire. The top of the soldered tab is where you put the wire and to make it stick, just press it down until the solder cools off. .

4) Now what do you see across the back of the solar cells? Two lines of copper wire! The setup goes like this: The negative end of the wire goes to the negative slot and positive enters the positive slot.

5)  Time to link up the cells! Arrange the wiring in such way that the negative wires are unable to come into touch with the positive wires.

6) Drill 2 holes to get the wire out of the back of the plywood panel, add the wood to form a border around the cells, screw from the back and finally with the silicone sealant in hand put the Plexiglass sheet on top of the panel.

Keep in mind that, if you watch step-by-step video tutorials like I have, then it will be a whole lot easier to make homemade solar panel!